top of page

ADVERT & SIGNS.

ADVERT & SIGNS.

3M DI-NOC and Architectural Film in Singapore: Refresh Offices, Shops and Lifts Without Renovating

Writer: Advert & Signs Team
Advert & Signs Team
11 hours ago
4 min read

Short answer: 3M DI-NOC is a 0.2 mm self-adhesive vinyl film that recreates wood, stone, metal and solid finishes on existing surfaces. Singapore offices, shops and buildings use it to refresh doors, counters, columns, lifts and cabinetry with little noise or dust. 3M rates it for about 12 years indoors. Keep it off the walls of exit staircases and exit passageways.

Infographic: 3M DI-NOC at a glance. 0.2 mm thick, 900+ designs, 12 years indoor durability, applied at 12 to 38 degrees Celsius.

What is 3M DI-NOC?

DI-NOC is 3M's range of architectural finishes: decorative vinyl films applied on site over the surfaces you already have. According to 3M:

  • the film is about 200 microns (0.2 mm) thick, with a pressure-sensitive adhesive;

  • 3M's Comply air-release channels help push out bubbles during application;

  • there are more than 900 patterns, colours and textures, including woodgrain, stone, metal, leather and solid colours;

  • most interior films are rated Class A for fire under ASTM E84, and the range is also tested to EN 13501;

  • 3M rates the film at 12 years' durability for indoor applications;

  • it resists common stains, cleaners and disinfectants;

  • it is applied between 12 and 38°C, and 3M lists it as not removable.

Other makers produce similar interior films, such as LX Hausys. Whichever brand you use, the principles in this guide are the same: specify by the product's data sheet, not by its name.

Where does architectural film work in commercial spaces?

Surface

Typical use

Watch out for

Office doors and frames

Refresh or rebrand a whole floor

Fire-rated doors: check certification first (see our door wrapping guide)

Reception counters and feature walls

Put brand colours and finishes where visitors look first

Kicks at the base: use an abrasion-resistant film or a kick plate

Lift car interiors and lift doors

Update tired lifts without replacing panels

Building owner and lift contractor consent, and an off-peak schedule

Columns and beams

Stone, metal or timber looks

Corners and edges need careful heat-forming

Pantry and meeting-room cabinetry

Match carpentry to a new scheme

Heat and water near sinks and coffee machines

Retail fixtures and display counters

Seasonal or brand refreshes

High-wear edges

Partitions and ceilings

Large surfaces changed without demolition

Access and scaffolding

3M also makes an abrasion-resistant DI-NOC series for high-traffic areas, an exterior series for flat and simply curved outdoor surfaces, and a whiteboard film for meeting rooms.

Why choose film over renovation?

  • Less disruption: 3M says DI-NOC installs with less downtime, noise and disruption than traditional materials. In many cases no power tools are needed.

  • Lower cost: 3M says DI-NOC is more cost-effective than traditional construction materials, because the substrate stays and there is little demolition waste.

  • Easier repairs: a damaged area can be patched, and 3M says repairs are virtually invisible at normal viewing distance.

  • Hygiene: the film resists common cleaners and disinfectants, which matters for clinics, F&B and shared offices.

Fire safety and approvals

Film is thin, but it is still a wall or door finish, so check these before you specify it.

  • Exit routes. Under Singapore's Fire Code 2023, clause 3.13, wall and ceiling finishes in the form of thin sheet no more than 1.0 mm thick, mounted on a non-combustible substrate, are not subject to the surface spread of flame provisions, except in exit staircases and passageways. Keep decorative film off the walls and ceilings of those spaces unless your Qualified Person has confirmed it complies, and check the substrate is non-combustible elsewhere.

  • Fire-rated doors. A fire door is a certified product. Don't film one without confirmation from its manufacturer or certification body that a surface film is allowed, and never cover the fire-rating label.

  • Landlord, MCST and mall fit-out rules. Most commercial leases need written approval for changes to finishes, especially in common areas and lifts.

  • Lifts. The building owner and the lift maintenance contractor should agree to the work and its timing.

3M's Class A rating is a US test classification. Your Qualified Person should confirm how the chosen film meets Singapore's Fire Code for the location.

What does DI-NOC cost?

Architectural film is usually priced per square metre of film plus labour. Labour depends on how complex the surface is: flat doors are quick, while columns, grooves and three-dimensional corners take longer. Lift interiors and after-hours work add to the cost.

No Singapore installer publishes a standard per-square-metre rate for DI-NOC, because labour varies so much with the surface. Expect a quote after a site visit, itemised by area and by item (doors, counters, lift panels).

How long does it last?

3M rates DI-NOC at 12 years' durability for indoor applications. The technical data sheet specifies indoor, vertical surfaces, so counters and other horizontal surfaces will wear sooner. Abrasion-resistant films and good edge detailing extend its life in busy areas.

Who should install it?

3M recommends using a DI-NOC Preferred Installer, trained on 3M's installation techniques. 3M runs a two-day installer training course that leads to Preferred Installer status. When you compare quotes, ask whether the installer has been trained on DI-NOC.

Applying vinyl is already core to our signage work, from glass frosting to large wall decals and murals. We fabricate in our own workshop at JTC Space @ Tuas, and we are bizSAFE Level 3.

FAQ

Is DI-NOC better than repainting?

They do different jobs. Paint suits plain walls. DI-NOC gives you textures and realistic wood, stone and metal finishes that paint can't, and it doesn't need drying time.

Can DI-NOC be used outdoors?

Only the exterior (EX) series, and only on flat or simply curved surfaces, according to 3M. The standard interior films are for indoor use.

Can it be removed later?

3M lists DI-NOC as not removable, so plan it as a permanent finish. Tenants should agree this with the landlord before work starts.

Can you apply it to metal lift panels?

3M says DI-NOC bonds to virtually any substrate, and lifts and metal panels are common applications. The surface must be clean, sound and properly primed.

How do I clean it?

Wipe with a soft cloth and mild detergent. 3M says the film resists common cleaners and disinfectants. Avoid abrasive pads.

How do I get a quote?

Send us photos, rough dimensions and the finish you have in mind on WhatsApp at +65 9862 5243, or see our vinyl wrap service. For offices, see also our guide to office signage.

Sources

Comments


bottom of page